Emerald Full ECU wiring loom – Ford Duratec engine

£250.00

In stock

Emerald full wiring loom (harness) with various optimisation options for installation of our standalone ECU on Ford Duratec engines.

Description

A complete general wiring loom for Ford Duratec engine installations. Designed to fit most cars and available in two variations of length for both, K3 ECU and K6 ECU:

* Short – for fitment of our ECU in engine bay.
* Long – for fitment of our ECU inside cab.

and two variations of Coil setup:

* Coil pack.
* Coil on plug (4 separate coils)(K6 ECU only).

Supports both Sequential and Semi-sequential injection options. This loom simply requires installation onto the Duratec engine, mounting of the integral fuse block and relays and +12v power and earth connections. Then just plug in our ECU and away you go.

The loom is produced using high spec automotive wiring and connectors throughout to provide a robust wiring solution that can be relied on – for both road and race installations. It is designed to connect directly to a combination of the Duratec’s original sensors and Emerald supplied sensors/actuators. All wires are twisted to avoid any possible interference and labeled for easy installation.

Specs:
(length shown from ECU to connection)

* Crank Sensor (shielded) 2,225mm (short 1,675mm) – OE Ford connector or 2-pin Junior mini timer
* Cam Sensor (shielded) 1,225mm (short 675mm) – OE Ford connector or 2-pin Junior mini timer
* Coil Pack 925mm (short 375mm) – Ford GEN 2 connector or Ford (late gen.) coil pack plug
* Air Temp 1,700mm (short 1,150mm) – Junior Mini Timer connector
* Water Temp 1,300mm (short 750mm) – Junior Mini Timer connector
* TPS 1,350mm (short 800mm) – Superseal connector
* Lambda 1,525mm (short 975mm) – Superseal connector
* Injectors – Junior Mini Timer connector or EV6 connector
Inj. 1 – 1,450mm (short 900mm)
Inj. 2 – 1,350mm (short 800mm)
Inj. 3 – 1,250mm (short 700mm)
Inj. 4 – 1,150mm (short 600mm)

Coil on plug – unterminated (OE Ford coil plugs optional)
Coil 1 – 1,450mm (short 900mm)
Coil 2 – 1,350mm (short 800mm)
Coil 3 – 1,250mm (short 700mm)
Coil 4 – 1,150mm (short 600mm)

Pre-wired provision for the following outputs is also built into the loom with 10-way plug (both sides of the plug provided):

* Fuel Pump +12v
* Coolant Fan Relay
* Shift-light (not included with Coil on plug option)
* Tacho driver
* Battery +12v
* Battery ground

Please check your requirements before ordering. If any details above are not satisfactory please contact us for customisation. Full custom looms also available. E-mail us at sales@emeraldm3d.co.uk or call on +44 (0) 1953 889110 and we will do our best to provide you with a solution.

Please note that this loom is made to order and may take longer to ship.

Additional information

Weight 1.3500 kg

Related products

  • Emerald K6 ECU P&P adapter – Lotus Elise S2 (A/C, non VVC), 1.8 K-Series

    £145.00
  • FREE Remote support

    £0.00
  • 4 Cylinder wiring loom (harness) for Emerald ECU

    £190.00
  • Emerald K6 ECU Plug & Play adapter – Lotus Elise S2 (Inc. VVC), 1.8 K-Series engine

    £145.00
View all products

What our customers say about us

  • Incredible work from Oli at Emerald. Very thorough and talked me through every process to ensure I was informed and happy! Mechanic Keith popped in to lend a hand, who is also very friendly and professional. Enormous passion and enthusiasm for their work. Excellent service throughout. Very pleased! Thanks again guys.

    +

    Luke Blunt

  • Hugely recommend Karl and the team at Emerald ECUs. They provide a very dedicated and knowledgeable service as well as an excellent ECU – going by my experience. I had my troublesome ECU replaced (made by another Norfolk company) by Emerald after Clive Atthowe Tuning in Norwich recommended Emerald to me. My classic Citroen is now a different car altogether – it is quieter, it pulls away more smoothly at low revs and I can put my foot down without the engine pinking. Some other minor glitches spotted by Karl were also fixed, for example the tachometer would not run with the old ECU. Plus I think the price was very reasonable considering how many hours they probably put into the swap, retune and minor fixes. My five-star rating and this description of how pleased I am with Emerald just touches the surface.

    +

    Bruce Lankford

  • I bought a kit car recently with 2.0 zetec engine. it had a few issues, loss of power etc. The guys at Emerald were absolutely amazing. They fixed several problems, throttle not opening fully, faulty thermostat (they cad designed and laser cut a new gasket) and some other mechanical issues. They then remapped the K6 ECU and it comes out to 160bhp which I was over the moon with for a relatively stock engine with single throttle body plenum. It’s like a completely different car now, sounds better, runs better, no issues with idle anymore and the best part, it’s ridiculously fast and blew my socks off. Can’t thank everyone at Emerald enough, they stayed late to ensure everything was ironed out and running as it should. You won’t get better service than this anywhere in the country. The extra work they do to make sure your car is running to the best of its ability is second to none, some people online grumble at the cost for the day but I’d pay that twice over, don’t take it to a normal rolling road as remapping a car is useless if there are other issues restricting the cars performance. I’ll always take my cars to them now. A class service.

    +

    Chris Mitchell

  • I went for a K6 ECU as they had been recommended by various friends and colleagues. It’s a fantastic option for a relative novice to this side of car building. The interface is brilliant and it is a really neat product. Best of all is the incredible customer service provided by the after sales team. Second to none.

    +

    Rich Harrison

  • Dave set up my K Series’s Midget yesterday on the Rolling Road. Did a fantastic job and the car is running beautifully. Thank you all at Emerald. Highly recommended.

    +

    Neil Thomas

  • I purchased a second-hand car in the last month which had been to Emerald 5 years ago (!) for mapping/tuning work. I reached out to Emerald just on the off chance they’d remember the car as I had some questions about the car and the map on it’s Emerald K6+ ECU and everyone at Emerald has been amazingly helpful. Karl and Dave have spent a not insignificant amount of time on email/phone/teamviewer with me to walk through the queries I had and helping me to resolve some issues. Absolutely fantastic service! 10/10

    +

    Don Morrison

Read more testimonials on

or